Crimestopper-security-products CS-2008PC User Manual

Browse online or download User Manual for Car alarm Crimestopper-security-products CS-2008PC. Crimestopper Security Products CS-2008PC User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 19
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
CS-2008PC SecurLinc™
ADVANCED REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
*NOTE: There are several features of the CS-2008PC system that can only be accessed and/or programmed
by using optional SecurLinc™ PC software and data cable via the system’s expansion port via a Personal
Computer: An expansion kit is available which includes Software, PC linc cable and a power supply (SLA-50)
Assigning the amount of time for a “Timed” Auxiliary output channel.
Assigning Self-start temperature and voltage-drop thresholds (when using the remote start expansion
module).
“Secure Disarm” using a 4-press transmitter button sequence.
Inputs & Outputs testing and diagnostics of main system
Inputs & Outputs testing of Data Linc expansion modules i.e. Remote Start, 2-Way pager, & Aux. channel
module.
Quick & Easy option programming
Erasing transmitter codes
Adjusting Glow plug delay time, Voltage Drop Threshold
PRE-INSTALLATION CAUTIONS & WARNINGS
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR
BAGS, ABS BRAKES, ENGINE COMPUTERS, BATTERY etc.).
WE RECOMMEND the use of a VOLT/OHM METER to test and verify wiring circuits. Test lights or illuminated
probes can cause damage to on-board computer or engine management systems.
DO NOT exceed maximum output ratings or damage may occur. Electrical current limits for this alarm are
listed where applicable on the system diagram (Pg. 16). If you are unsure about the current load, of a specific
circuit on your vehicle, measure the load first with an amp-meter before connecting.
WE RECOMMEND that the MAIN SYSTEM FUSE be REMOVED before jump starting, using a battery
charger, or changing the battery. A voltage surge or high boost condition could damage alarm circuits.
DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering
column, or any other moving parts in the vehicle.
TECH SUPPORT
This device complies with FCC Rules part 15.
Operation is subject to the following two conditions: 1)
This device may not cause interference, and (2) this
device must accept any interference that may be
received, including interference that may cause
undesired operation. The manufacturer is not
responsible for any radio or TV interference caused by
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
Website: www.crimestopper.com
REV. A 02/2003 SW:
Page view 0
1 2 3 4 5 6 ... 18 19

Summary of Contents

Page 1 - CS-2008PC SecurLinc™

CS-2008PC SecurLinc™ ADVANCED REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS *NOTE: There are several features

Page 2 - CONTROL MODULE MOUNTING

REMOTE TRANSMITTER PROGRAMMING 1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF, ON/OFF, ON) You should hear (3) c

Page 3 - COMPONENT MOUNTING

OPTION PROGRAMMING TABLE PROGRAMMING OPTIONS CHART * = Default (Column 1) Option # Option Description BUTTON 1* LOCK BUTTON 2 UNLOCK BUTTON 3

Page 4

OPTION DESCRIPTIONS 2. ACTIVE RE-ARMING / HANDS-FREE IMMOBILIZER This option controls the Active Re-arming feature and the Hands-free immobilizer. T

Page 5 - SYSTEM WIRING DIAGRAM #1

OPTION PROGRAMMING 12. HORN OUTPUT / CARJACK WITH HANDS-FREE REMOTE (2 FEATURES) This option controls whether the system’s Factory Horn output AND fu

Page 6 - SYSTEM WIRING DIAGRAM #2

OPTION RESET TO RESTORE ALL PROGRAMMABLE OPTIONS TO DEFAULT VALUES (*): 1. Turn the Ignition ON and press the Program/Override button 5 times. The

Page 7 - VALET/PROGRAM

“HANDS FREE” REMOTE CONTROL (OPTIONAL) This 2008PC system is compatible with an optional “Hands-free” remote transmitters (not included in kit). The

Page 8 - POWER DOOR LOCK WIRING

HANDS-FREE PROGRAMMING & SETUP NOTE: PASSIVE ARMING AND PASSIVE LOCKING MUST BE ENABLED ALONG WITH THE HANDS-FREE MODE. ENABLE HANDS FREE MODE:

Page 9

5-BUTTON REMOTE OPERATION: 5-Button One-Way Remote Functions: PANICBUTTON 1BUTTON 3BUTTON 2BUTTON 4BUTTON 5(ON SIDE) BANK #1 (Directly Press Buttons)

Page 10 - OPTION PROGRAMMING

ALARM OPERATION PANIC FEATURE: In the event of an emergency situation or to attract attention to your vehicle, press and hold Button #4 (Panic). The

Page 11 - OPTION DESCRIPTIONS

ALARM OPERATION DOME LIGHT ILLUMINATION: (Optional) This feature turns on the vehicle’s dome light upon disarm for 30 seconds or until the key is ins

Page 12

TABLE OF CONTENTS Pre-Installation Cautions & Warnings…….…………………………………………………………..………………1 Control Module & Component Mounting…………………..…………………

Page 13

COMPONENT MOUNTING SIREN: Mount the siren under the hood to an inner fender-well, wheel-well, or other body surface with the open end facing downward

Page 14 - OPTION RESET

WIRING PIN 12: ORANGE WIRE: NEGATIVE ARMED OUTPUT – Starter Disable (500mA Ground, Optional) This wire becomes a (-) Ground output when system is ar

Page 15 - HANDS-FREE TRANSMITTER

SYSTEM WIRING DIAGRAM #1

Page 17 - 5-BUTTON REMOTE OPERATION:

SHOCK SENSOR DUAL ADJUST Smart Sense™ Shock Sensor: GREENREDPre-WarnTrigger The supplied dual stage / dual adjust shock sensor does not require any a

Page 18

POWER DOOR LOCK WIRING GREEN: (-) LOCK / (+) UNLOCK BLUE: (-) UNLOCK / (+) LOCK COMMON DOOR LOCK TYPES: (SEE FOR DESCRIPTIONS) Negative Trigger (-)

Page 19

POWER DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRINGPOSITIVE TRIGGER DOORLOCK WIRINGGREENGREENBLUEBLUEDIODESFACTORYFACTORYLLLOCKLOCKPOWERPOWERLOCKI

Comments to this Manuals

No comments